Avigilon POE-INJ2-60W-NA 60W Single-Port Gigabit PoE++ Injector

Avigilon POE-INJ2-60W-NA 60W Single-Port Gigabit PoE++ Injector

The Avigilon POE-INJ2-60W-NA is a single-port, 60 W Gigabit PoE++ injector that powers high-draw Avigilon cameras over one Ethernet cable. It delivers power on all four wire pairs with power isolation, so it can sit between any network switch and the camera without changing the switch's PoE or LLDP settings. Avigilon lists it as a power option for the H4 IR PTZ, H4 PTZ pendant dome and H4 Multisensor cameras.

Key Specifications

Full specifications are listed in the Detailed Specifications tab.

Why Choose the Avigilon POE-INJ2-60W-NA?

• Up to 60 W from a single injector, enough for Avigilon PTZ and multisensor cameras
• Gigabit data pass-through on one port
• Power on all four wire pairs, with power isolation
• Works with any network switch, with no need to disable PoE or LLDP negotiation
• Listed by Avigilon for the H4 IR PTZ, H4 PTZ pendant and H4 Multisensor cameras
• Indoor injector for network closets and equipment rooms

Important: Avigilon Proprietary Pin-Out

Avigilon states that its 60 W and 95 W PoE++ injectors were developed before the IEEE 802.3bt standard was finalized and use a proprietary power and pin-out arrangement. That makes them incompatible with devices designed for non-Avigilon PoE injectors with different power specifications, so match this injector to the Avigilon cameras that list it. On Avigilon injectors, pins 1 and 2 are negative and pins 3 and 6 positive on channel 1 (the reverse of standard 802.3bt), while channel 2 matches the standard: pins 4 and 5 positive, pins 7 and 8 negative.

Compatible Avigilon Cameras

Avigilon lists the 60 W PoE++ injector as a power option for these cameras. Contact us to order any of them:

• Avigilon H4 IR PTZ camera
• Avigilon H4 PTZ pendant dome camera
• Avigilon H4 Multisensor camera (H4A-xMH) when the IR ring is used
• Avigilon H5A Multisensor camera, with the camera's PoE mode switch set to position A

Installation Notes

Connect the network switch to the injector's data input and the camera's Ethernet cable to the PoE output. The injector operates from -10 °C to +45 °C (14 °F to 113 °F) and is meant for indoor installation. If an H5A Multisensor camera shows no power LEDs, open its back cover and set the PoE mode switch to position A, which provides compatibility with legacy high-power PoE injectors.

Typical Applications

• Powering Avigilon H4 PTZ cameras on campus perimeters and parking lots
• Powering Avigilon multisensor cameras on building corners and large lots
• Adding high-power cameras to a network whose switch cannot supply 60 W

Compare Avigilon PoE Injectors

Explore More

• Browse PoE Devices at Affinitech Store
• Shop Power Supplies for network cameras
• Explore Avigilon products at Affinitech Store

Frequently Asked Questions About the Avigilon POE-INJ2-60W-NA

How much power does the Avigilon POE-INJ2-60W-NA supply?

Up to 60 W over a single Ethernet cable, delivered on all four wire pairs.

Is it an IEEE 802.3bt injector?

No. Avigilon states that its 60 W and 95 W PoE++ injectors were developed before the 802.3bt standard was finalized and use a proprietary power and pin-out arrangement.

Can it power non-Avigilon devices?

Avigilon notes that the proprietary pin-out makes these injectors incompatible with devices built for non-Avigilon PoE injectors with different power specifications. Use it with the Avigilon cameras that list it as a power option.

Which cameras is it used with?

Avigilon lists the 60 W injector as a power option for the H4 IR PTZ camera, the H4 PTZ pendant dome camera and the H4 Multisensor camera with the IR ring. It also works with H5A Multisensor cameras when the camera's PoE mode switch is set to position A.

Does it work with my existing network switch?

Yes. Because it supplies power on all wire pairs with power isolation, Avigilon states it can be used on any type of network switch without disabling PoE or LLDP negotiation on the switch.

Why does my H5A Multisensor camera show no power LEDs with this injector?

Set the PoE mode switch inside the camera's back cover to position A, which provides compatibility with legacy high-power PoE injectors, then reconnect the injector. Position B is the default.

What is the operating temperature range?

The injector operates from -10 °C to +45 °C (14 °F to 113 °F) and is designed for indoor use. With the H4 IR PTZ camera, Avigilon specifies a reduced camera operating range of -10 °C to +50 °C.

How many ports does it have?

It is a single-port injector: one Ethernet data input and one Gigabit PoE output.

Can I use a PoE switch instead?

For the H4 IR PTZ and H4 PTZ pendant cameras, Avigilon also lists a Cisco UPoE switch supporting 60 W over four pairs (with Force Four Pair enabled) or an external power supply as alternatives.